In the Linux kernel, the following vulnerability has been resolved:
batman-adv: bla: fix report_work leak on backbone_gw purge
batadv_bla_purge_backbone_gw() removes stale backbone gateway entries,
but fails to properly handle their associated report_work:
- If report_work is running, the purge must wait for it to finish before
freeing the backbone_gw, otherwise the worker may access freed memory
(e.g. bat_priv).
- If report_work is pending, the purge must cancel it and release the
reference held for that pending work item.
The previous implementation called hlist_for_each_entry_safe() inside a
spin_lock_bh() section, but cancel_work_sync() may sleep and therefore
cannot be called from within a spinlock-protected region.
Restructure the loop to handle one entry per spinlock critical section:
acquire the lock, find the next entry to purge, remove it from the hash
list, then release the lock before calling cancel_work_sync() and
dropping the hash_entry reference. Repeat until no more entries require
purging.
In the Linux kernel, the following vulnerability has been resolved:
spi: ti-qspi: fix use-after-free after DMA setup failure
The driver falls back to PIO mode if DMA setup fails during probe.
Make sure to clear the DMA channel pointer also if buffer allocation
fails to avoid passing a pointer to the released channel to the DMA
engine (or trying to free the channel a second time on late probe errors
or driver unbind).
This issue was flagged by Sashiko when reviewing a devres allocation
conversion patch.
In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mld: don't dereference a pointer before NULL checking it
In iwl_mld_remove_link, the link->fw_id is saved at the beginning of the
function so we have it after we freed the link.
But the link pointer can be NULL, and is not checked when the fw_id is
stored.
Fix it by simply freeing the link at the end of the function.
fFixes: 0e66a39f4f0e ("wifi: iwlwifi: fix potential use after free in iwl_mld_remove_link()")
In the Linux kernel, the following vulnerability has been resolved:
i2c: stub: Reject I2C block transfers with invalid length
The I2C_SMBUS_I2C_BLOCK_DATA case in stub_xfer() uses data->block[0]
as the transfer length. The existing check only clamps it to avoid
overrunning the chip->words[256] register array, but does not validate
it against I2C_SMBUS_BLOCK_MAX (32), which is the limit of the union
i2c_smbus_data.block buffer (34 bytes total). The driver is a
development/test tool (CONFIG_I2C_STUB=m, not built by default)
that must be loaded with a chip_addr= parameter.
A local user with access to /dev/i2c-* can issue an I2C_SMBUS ioctl
with I2C_SMBUS_I2C_BLOCK_DATA and data->block[0] > 32, causing
stub_xfer() to read or write past the end of the union
i2c_smbus_data.block buffer:
BUG: KASAN: stack-out-of-bounds in stub_xfer (drivers/i2c/i2c-stub.c:223)
Read of size 1 at addr ffff88800abcfd92 by task exploit/81
Call Trace:
<TASK>
stub_xfer (drivers/i2c/i2c-stub.c:223)
__i2c_smbus_xfer (drivers/i2c/i2c-core-smbus.c:593)
i2c_smbus_xfer (drivers/i2c/i2c-core-smbus.c:536)
i2cdev_ioctl_smbus (drivers/i2c/i2c-dev.c:391)
i2cdev_ioctl (drivers/i2c/i2c-dev.c:478)
__x64_sys_ioctl (fs/ioctl.c:583)
do_syscall_64 (arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
</TASK>
The bug exists because i2c-stub implements .smbus_xfer directly,
bypassing the I2C_SMBUS_BLOCK_MAX validation in
i2c_smbus_xfer_emulated(). The I2C_SMBUS_BLOCK_DATA case in the same
function correctly validates against I2C_SMBUS_BLOCK_MAX, but the
I2C_SMBUS_I2C_BLOCK_DATA case does not.
Fix by rejecting transfers with data->block[0] == 0 or
data->block[0] > I2C_SMBUS_BLOCK_MAX with -EINVAL, consistent with
both the I2C_SMBUS_BLOCK_DATA case in the same function and the
I2C_SMBUS_I2C_BLOCK_DATA validation in i2c_smbus_xfer_emulated().
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: cancel pending_rx_work before taking conn->lock
l2cap_conn_del() takes conn->lock and then calls cancel_work_sync() for
pending_rx_work. process_pending_rx() takes the same mutex, so teardown
can deadlock against the worker it is flushing.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the l2cap_conn_ready() -> queue_work(...,
&conn->pending_rx_work) submit path, the l2cap_conn_del() ->
cancel_work_sync(&conn->pending_rx_work) teardown path, and the
process_pending_rx() -> mutex_lock(&conn->lock) worker edge. Lockdep
WARNING: possible circular locking dependency detected
process_pending_rx+0x21/0x2a [vuln_msv]
l2cap_conn_del.constprop.0+0x3f/0x4e [vuln_msv]
*** DEADLOCK ***
Cancel pending_rx_work before taking conn->lock, matching the existing
lock-before-drain ordering used for the two delayed works in the same
teardown path. The pending_rx queue is still purged after the work has
been cancelled and conn->lock has been acquired.
In the Linux kernel, the following vulnerability has been resolved:
xfs: fail recovery on a committed log item with no regions
If the first op of a transaction is a bare transaction header
(len == sizeof(struct xfs_trans_header)), xlog_recover_add_to_trans()
adds an item but no region, leaving it on r_itemq with ri_cnt == 0 and
ri_buf == NULL.
The header can be split across op records, so later ops may still add
regions; the item is only invalid if the transaction commits with none.
The runtime commit path never emits such a transaction, so this only
happens on a crafted log. It came from an AI-assisted code audit of the
recovery parser.
xlog_recover_reorder_trans() calls ITEM_TYPE() on the item, which reads
*(unsigned short *)item->ri_buf[0].iov_base and faults on the NULL
ri_buf. Reject it there, before the commit handlers that also read
ri_buf[0].
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:xlog_recover_reorder_trans (fs/xfs/xfs_log_recover.c:1836)
xlog_recover_commit_trans (fs/xfs/xfs_log_recover.c:2043)
xlog_recover_process_data (fs/xfs/xfs_log_recover.c:2501)
xlog_do_recovery_pass (fs/xfs/xfs_log_recover.c:3244)
xlog_recover (fs/xfs/xfs_log_recover.c:3493)
xfs_log_mount (fs/xfs/xfs_log.c:618)
xfs_mountfs (fs/xfs/xfs_mount.c:1034)
xfs_fs_fill_super (fs/xfs/xfs_super.c:1938)
vfs_get_tree (fs/super.c:1695)
path_mount (fs/namespace.c:4161)
__x64_sys_mount (fs/namespace.c:4367)
In the Linux kernel, the following vulnerability has been resolved:
net: qualcomm: rmnet: fix endpoint use-after-free in rmnet_dellink()
rmnet_dellink() removes the endpoint from the hash table with
hlist_del_init_rcu() and then immediately frees it with kfree(). However,
RCU readers on the receive path (rmnet_rx_handler ->
__rmnet_map_ingress_handler) may still hold a reference to the endpoint and
dereference ep->egress_dev after the memory has been freed. The endpoint is
a kmalloc-32 object, and the stale read at offset 8 corresponds to the
egress_dev pointer.
BUG: unable to handle page fault for address: ffffffffde942eef
Oops: 0002 [#1] SMP NOPTI
CPU: 1 UID: 0 PID: 137 Comm: poc_write Not tainted 7.0.0+ #4 PREEMPTLAZY
RIP: 0010:rmnet_vnd_rx_fixup (rmnet_vnd.c:27)
Call Trace:
<TASK>
__rmnet_map_ingress_handler (rmnet_handlers.c:48 rmnet_handlers.c:101)
rmnet_rx_handler (rmnet_handlers.c:129 rmnet_handlers.c:235)
__netif_receive_skb_core.constprop.0 (net/core/dev.c:6096)
__netif_receive_skb_one_core (net/core/dev.c:6208)
netif_receive_skb (net/core/dev.c:6467)
tun_get_user (drivers/net/tun.c:1955)
tun_chr_write_iter (drivers/net/tun.c:2003)
vfs_write (fs/read_write.c:688)
ksys_write (fs/read_write.c:740)
</TASK>
Add an rcu_head field to struct rmnet_endpoint and replace kfree() with
kfree_rcu() so the endpoint memory remains valid through the RCU grace
period. Also remove the rmnet_vnd_dellink() call and inline only the
nr_rmnet_devs decrement, since rmnet_vnd_dellink() would set
ep->egress_dev to NULL during the grace period, creating a data race
with lockless readers.
In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tp_meter: directly shut down timer on cleanup
batadv_tp_sender_cleanup() was calling timer_delete_sync() followed by
timer_delete() to guard against the timer handler re-arming itself between
the two calls. This double-deletion hack relied on the sending status being
set to 0 to suppress re-arming.
Replace both calls with a single timer_shutdown_sync(). This function both
waits for any running timer callback to complete (like timer_delete_sync())
and permanently disarms the timer so it cannot be re-armed afterwards,
making re-arming prevention unconditional and self-documenting.
The re-arming property is also required because otherwise:
1. context 0 (batadv_tp_recv_ack()) checks in
batadv_tp_reset_sender_timer() if sending is still 1 -> it is
2. context 1 changes in batadv_tp_sender_shutdown() sending to 0 and in
this process forces the kthread to stop timer in
batadv_tp_sender_cleanup()
3. context 0 continues in batadv_tp_reset_sender_timer() and rearms the
timer -> but the reference for it is already gone
In the Linux kernel, the following vulnerability has been resolved:
batman-adv: mcast: fix use-after-free in orig_node RCU release
batadv_mcast_purge_orig() removes entries from RCU-protected hlists but
does not wait for an RCU grace period before returning. Concurrent RCU
readers may still accesses references to those entries at the point of
removal. RCU-protected readers trying to operate on entries like
orig->mcast_want_all_ipv6_node will then access already freed memory.
Fix this by moving batadv_mcast_purge_orig() to batadv_orig_node_release(),
just before the call_rcu() invocation. This ensures RCU readers that were
active at purge time have drained before the orig_node memory is reclaimed.
In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Validate GPIO pin LUT table size before iterating
[Why&How]
The GPIO pin table parsers in get_gpio_i2c_info() and
bios_parser_get_gpio_pin_info() derive an element count from the VBIOS
table_header.structuresize field, then iterate over gpio_pin[] entries.
However, GET_IMAGE() only validates that the table header itself fits
within the BIOS image. If the VBIOS reports a structuresize larger than
the actual mapped data, the loop reads past the end of the BIOS image,
causing an out-of-bounds read.
Fix this by calling bios_get_image() to validate that the full claimed
structuresize is accessible within the BIOS image before entering the
loop in both functions.
(cherry picked from commit ba5e95b43b773ae1bf1f66ee6b31eb774e65afe3)