In the Linux kernel, the following vulnerability has been resolved:
spi: ti-qspi: fix use-after-free after DMA setup failure
The driver falls back to PIO mode if DMA setup fails during probe.
Make sure to clear the DMA channel pointer also if buffer allocation
fails to avoid passing a pointer to the released channel to the DMA
engine (or trying to free the channel a second time on late probe errors
or driver unbind).
This issue was flagged by Sashiko when reviewing a devres allocation
conversion patch.
In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: xsk: Fix unlocked writing to ICOSQ
During napi poll, when the affinity changes and there's still XSK work
to be done, we trigger an ICOSQ interrupt on the new CPU. However, this
triggering on the ICOSQ is done unprotected.
There are 2 such races:
A) mlx5e_trigger_irq() is called while mlx5e_xsk_alloc_rx_mpwqe() is
running from a different CPU due to affinity change. This can happen
because IRQ triggering is done after napi_complete_done(). At this point
the NAPI can be scheduled on a different CPU. Like this:
CPU A (old affinity, NAPI tail) CPU B (new affinity, fresh NAPI)
------------------------------- --------------------------------
napi_complete_done() clears SCHED
mlx5e_cq_arm(...)
napi_schedule_prep() sets SCHED
mlx5e_napi_poll()
mlx5e_xsk_alloc_rx_mpwqe()
mlx5e_icosq_sync_lock() // noop
memcpy 640 B UMR body
advance sq->pc by 10
mlx5e_trigger_irq(&c->icosq)
wqe_info[pi] = {NOP, 1}
mlx5e_post_nop() advances sq->pc
B) mlx5e_trigger_irq() is called on the ICOSQ when
mlx5e_trigger_napi_icosq() is running.
The obvious fix would be to lock the ICOSQ. But ICOSQ has an optimized
locking scheme that doesn't work for this scenario. Kick the async ICOSQ
instead which is always locked.
This issue was noticed in the wild with the following splat:
netdevice: ge-0-0-1: Bad OP in ICOSQ CQE: 0xd
WARNING: drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:826 [...]
[...]
Call Trace:
<IRQ>
mlx5e_napi_poll+0x11d/0x7f0 [mlx5_core]
__napi_poll+0x30/0x200
? skb_defer_free_flush+0x9c/0xc0
net_rx_action+0x2fe/0x3f0
handle_softirqs+0xd8/0x340
__irq_exit_rcu+0xbc/0xe0
common_interrupt+0x85/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x26/0x40
[...]
---[ end trace 0000000000000000 ]---
mlx5_core 0000:08:00.0 ge-0-0-1: Error cqe on cqn 0x548, ci 0x2022, qn 0x8f4,
opcode 0xd, syndrome 0x2, vendor syndrome 0x68
00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000030: 00 00 00 00 01 00 68 02 01 00 08 f4 de 14 59 d2
WQE DUMP: WQ size 16384 WQ cur size 0, WQE index 0x1e14, len: 64
00000000: 00 00 00 01 d9 ed 80 02 00 00 00 01 d9 ed 90 02
00000010: 00 00 00 01 d9 ed a0 02 00 00 00 01 d9 ed b0 02
00000020: 00 00 00 01 d9 ed c0 02 00 00 00 01 d9 ed d0 02
00000030: 00 00 00 01 d9 ed e0 02 00 00 00 01 d9 ed f0 02
mlx5_core 0000:08:00.0 ge-0-0-1: Error cqe on cqn 0x548, ci 0x2023, qn 0x8f4,
opcode 0xd, syndrome 0x5, vendor syndrome 0xf9
00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00000030: 00 00 00 00 01 00 f9 05 01 00 08 f4 de 15 cf d2
In the Linux kernel, the following vulnerability has been resolved:
srcu: Don't queue workqueue handlers to never-online CPUs
While an srcu_struct structure is in the midst of switching from CPU-0
to all-CPUs state, it can attempt to invoke callbacks for CPUs that
have never been online. Worse yet, it can attempt in invoke callbacks
for CPUs that never will be online, even including imaginary CPUs not in
cpu_possible_mask. This can cause hangs on s390, which is not set up to
deal with workqueue handlers being scheduled on such CPUs. This commit
therefore causes Tree SRCU to refrain from queueing workqueue handlers
on CPUs that have not yet (and might never) come online.
Because callbacks are not invoked on CPUs that have not been
online, it is an error to invoke call_srcu(), synchronize_srcu(), or
synchronize_srcu_expedited() on a CPU that is not yet fully online.
However, it turns out to be less code to redirect the callbacks
from too-early invocations of call_srcu() than to warn about such
invocations. This commit therefore also redirects callbacks queued on
not-yet-fully-online CPUs to the boot CPU.
In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mld: don't dereference a pointer before NULL checking it
In iwl_mld_remove_link, the link->fw_id is saved at the beginning of the
function so we have it after we freed the link.
But the link pointer can be NULL, and is not checked when the fw_id is
stored.
Fix it by simply freeing the link at the end of the function.
fFixes: 0e66a39f4f0e ("wifi: iwlwifi: fix potential use after free in iwl_mld_remove_link()")
In the Linux kernel, the following vulnerability has been resolved:
hwmon: (lm90) Add lock protection to lm90_alert
Sashiko reports:
lm90_alert() executes in the smbus alert context and calls
lm90_update_confreg() to disable the hardware alert line, without
acquiring hwmon_lock.
Concurrently, sysfs write operations (such as lm90_write_convrate) hold
the hwmon_lock, temporarily modify data->config, and then restore it.
If an alert interrupt occurs concurrently with a sysfs write, the sysfs
path will overwrite the alert handler's modifications to data->config
and the hardware register.
This unintentionally re-enables the hardware alert line while the alarm is
still active, causing an interrupt storm.
Add the missing lock to lm90_alert() to solve the problem.
lakeFS through 1.83.0, fixed in commit 71a45ee, contains an authentication bypass vulnerability in the /setup_comm_prefs endpoint that allows unauthenticated attackers to overwrite operator metadata including email, name, and company after setup completion. Attackers can POST to this endpoint to modify security update preferences, disable security communications, and trigger falsified telemetry events using the legitimate installation ID.
Missing authentication for critical function in Microsoft Azure Kubernetes Service allows an unauthorized attacker to elevate privileges over a network.
Missing Authorization vulnerability in Apache HBase thrift and rest delegation service.
A scan operation in thrift/rest service has 3 steps, open, fetch(possible multiple times), close.
The open step will return an id which will be passed back to server for identifying the scanner instances stored at server side.
We missed the owner check in fetch and close steps which means a user can fetch rows from the scanner which is opened by other users, and close scanners which belongs to other users.
This issue affects Apache HBase:from 3.0.0-alpha-1 through 3.0.0-beta-1, from 2.6.0 through 2.6.5, from 2.5.0 through 2.5.14, through 2.4.*.
Users are recommended to upgrade to version 3.0.0-beta-2, 2.6.6 and 2.5.15, which fixes the issue.