Linux: >> Linux Kernel >> 3.1.3 Security Vulnerabilities
In the Linux kernel, the following vulnerability has been resolved:
ipv4: raw: reject IP_HDRINCL packets with ihl < 5
raw_send_hdrinc() validates that the caller-supplied IPv4 header
fits within the message length:
iphlen = iph->ihl * 4;
err = -EINVAL;
if (iphlen > length)
goto error_free;
if (iphlen >= sizeof(*iph)) {
/* fix up saddr, tot_len, id, csum, transport_header */
}
It does not, however, reject ihl < 5. For such a packet the
"if (iphlen >= sizeof(*iph))" branch is skipped, leaving the
crafted iphdr untouched, but the packet is still handed to
__ip_local_out() and onward. Downstream consumers that read
iph->ihl assume a sane value: net/ipv4/ah4.c:ah_output() in
particular subtracts sizeof(struct iphdr) from top_iph->ihl * 4
and passes the (signed-int-negative, then cast to size_t)
result to memcpy(), producing an OOB access of length close to
SIZE_MAX and a host kernel panic.
An IPv4 header with ihl < 5 is malformed by definition (RFC 791:
"Internet Header Length is the length of the internet header in
32 bit words ... Note that the minimum value for a correct header
is 5."). The kernel should not be willing to inject such a
packet into its own output path.
Reject "iphlen < sizeof(*iph)" alongside the existing
"iphlen > length" check. This matches the principle that locally
constructed packets that re-enter the IP stack must pass the same
basic sanity tests that a foreign packet would be subjected to.
Once this lands, the "if (iphlen >= sizeof(*iph))" wrapper around
the fixup branch becomes redundant; left in place to keep the
patch minimal and backport-friendly. A follow-up can unwrap it.
Note that commit 86f4c90a1c5c ("ipv4, ipv6: ensure raw socket
message is big enough to hold an IP header") ensures the message
buffer is large enough to hold an iphdr, but does not constrain
the self-reported iph->ihl.
Reachability: the malformed packet source is any caller with
CAP_NET_RAW, including an unprivileged process in a user+net
namespace on a kernel with CONFIG_USER_NS=y. The reproduced AH
crash also requires a matching xfrm AH policy on the outgoing
route; a container granted CAP_NET_ADMIN can install that state
and policy in its netns. Loopback bypasses xfrm_output, so the
trigger uses a real netdev.
Reproduced on UML + KASAN: kernel-mode fault at addr 0x0 with
memcpy_orig at the crash site. Same shape reproduces inside a
rootless Docker container with --cap-add NET_ADMIN on a stock
distro kernel.
CVSS Score
7.8
EPSS Score
0.001
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
scsi: isci: Fix use-after-free in device removal path
The ISCI completion tasklet is initialized in isci_host_alloc()
(drivers/scsi/isci/init.c:496) and scheduled from both MSI-X and legacy
interrupt handlers (drivers/scsi/isci/host.c:223,613).
isci_host_deinit() stops the controller and waits for stop completion,
but it never kills completion_tasklet before teardown continues. A
top-of-function tasklet_kill() is not sufficient here: interrupts are
only disabled when isci_host_stop_complete() runs, so until
wait_for_stop() returns the IRQ handlers can still requeue the
tasklet. The tasklet callback also re-enables interrupts after draining
completions, so killing the tasklet before the source is quiesced leaves
the same race open.
Once wait_for_stop() returns, no further IRQ-driven scheduling can
occur. Kill completion_tasklet there so teardown cannot race a queued
tasklet running on a dead ihost. On remove or unload, the stale callback
can otherwise dereference ihost and touch ihost->smu_registers after the
host lifetime ends.
A UML + KASAN analogue reproduced the failure class both with no
tasklet_kill() and with tasklet_kill() placed before source quiesce, and
stayed clean once the kill happened after quiescing the scheduling
source.
This mirrors commit f6ab594672d4 ("scsi: aic94xx: fix use-after-free in
device removal path"), but ISCI needs the kill after wait_for_stop().
CVSS Score
7.8
EPSS Score
0.001
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: fix negative tt_buff_len
batadv_orig_node::tt_buff_len was declared as s16, but the field is never
intended to hold a negative value. When a value greater than 32767 is
assigned, it wraps to a negative signed integer.
In batadv_send_other_tt_response(), tt_buff_len is temporarily widened to
s32. The incorrectly negative s16 value propagates into the s32, causing
batadv_tt_prepare_tvlv_global_data() to allocate a full sized buffer but
populates only a small portion of it with the collected changeset. All
remaining bits are kept uninitialized.
Using an u16 avoids this type confusion and ensures that no (negative) sign
extension is performed in batadv_send_other_tt_response().
CVSS Score
8.8
EPSS Score
0.003
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
batman-adv: tt: fix negative last_changeset_len
batadv_piv_tt::last_changeset_len len was declared as s16, but the field is
never intended to hold a negative value. When a value greater than 32767 is
assigned, it wraps to a negative signed integer.
In batadv_send_my_tt_response(), last_changeset_len is temporarily widened
to s32. The incorrectly negative s16 value propagates into the s32, causing
batadv_tt_prepare_tvlv_local_data() to allocate a full sized buffer but
populates only a small portion of it with the collected changeset. All
remaining bits are kept uninitialized.
Using an u16 avoids this type confusion and ensures that no (negative) sign
extension is performed in batadv_send_my_tt_response().
CVSS Score
9.8
EPSS Score
0.006
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
KVM: Replace guest-triggerable BUG_ON() in ioeventfd datamatch with get_unaligned()
Drop a BUG_ON() that has been reachable since it was first added, way back
in 2009, and instead use get_unaligned() to perform potentially-unaligned
accesses.
For a given store, KVM x86's emulator tracks the entire value in the
destination operand, x86_emulate_ctxt.dst. If the destination is memory,
and the target splits multiple pages and/or is emulated MMIO, then KVM
handles each fragment independently. E.g. on a page split starting at page
offset 0xffc, KVM writes 4 bytes to the first page, then the remaining
bytes to the second page, using ctxt->dst as the source for both (with
appropriate offsets).
If the destination splits a page *and* hits emulated MMIO on the second
page, then KVM will complete the write to the first page, then emulate the
MMIO access to the second page. If there is a datamatch-enabled ioeventfd
at offset 0 of the second page, then KVM will process the remainder of the
store as a potential ioeventfd signal.
Putting it all together, if the guest emits a store that splits a page
starting at page offset N, and the second page has a datamatch-enabled
ioeventfd at offset 0, then KVM will check for datamatch using
&dst.valptr[N] as the source. Due to dst (and thus dst.valptr) being
32-byte aligned, if N is not aligned to @len, the BUG_ON() fires.
E.g. with a 16-byte store at page offset 0xffc, to an ioeventfd of len 8,
all initial checks in ioeventfd_in_range() will succeed, and the BUG_ON()
fires due to @val being 4-byte aligned, but not 8-byte aligned.
------------[ cut here ]------------
kernel BUG at arch/x86/kvm/../../../virt/kvm/eventfd.c:783!
Oops: invalid opcode: 0000 [#1] SMP
CPU: 0 UID: 1000 PID: 615 Comm: repro Not tainted 7.1.0-rc2-ff238429d1ea #365 PREEMPT
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
RIP: 0010:ioeventfd_write+0x6c/0x70 [kvm]
Call Trace:
<TASK>
__kvm_io_bus_write+0x85/0xb0 [kvm]
kvm_io_bus_write+0x53/0x80 [kvm]
vcpu_mmio_write+0x66/0xf0 [kvm]
emulator_read_write_onepage+0x12a/0x540 [kvm]
emulator_read_write+0x109/0x2b0 [kvm]
x86_emulate_insn+0x4f8/0xfb0 [kvm]
x86_emulate_instruction+0x181/0x790 [kvm]
kvm_mmu_page_fault+0x313/0x630 [kvm]
vmx_handle_exit+0x18a/0x590 [kvm_intel]
kvm_arch_vcpu_ioctl_run+0xc81/0x1c90 [kvm]
kvm_vcpu_ioctl+0x2d5/0x970 [kvm]
__x64_sys_ioctl+0x8a/0xd0
do_syscall_64+0xb7/0x890
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x7f19c931a9bf
</TASK>
Modules linked in: kvm_intel kvm irqbypass
---[ end trace 0000000000000000 ]---
In a perfect world, the fix would be to simply delete the BUG_ON(), as KVM
x86 doesn't perform alignment checks on "normal" memory accesses at CPL0.
Sadly, C99 ruins all the fun; while the x86 architecture plays nice,
dereferencing an unaligned pointer directly is undefined behavior in C,
e.g. triggers splats when running with CONFIG_UBSAN_ALIGNMENT=y.
CVSS Score
7.1
EPSS Score
0.002
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
ocfs2: reject oversized group bitmap descriptors
ocfs2_validate_gd_parent() only bounds bg_bits against the parent
allocator's chain geometry. A malicious descriptor can still claim a
bg_size/bg_bits pair that exceeds the bitmap bytes that physically fit in
the group descriptor block, so later bitmap scans and bit updates can run
past bg_bitmap.
Add a physical-cap check based on ocfs2_group_bitmap_size() for the parent
allocator type and reject descriptors whose bg_size or bg_bits exceed that
capacity. Keep the existing chain geometry check so both the on-disk
bitmap layout and the allocator metadata must agree before the descriptor
is used.
Validation reproduced this kernel report:
KASAN use-after-free in _find_next_bit+0x7f/0xc0
Read of size 8
Call trace:
dump_stack_lvl+0x66/0xa0 (?:?)
print_report+0xd0/0x630 (?:?)
_find_next_bit+0x7f/0xc0 (?:?)
srso_alias_return_thunk+0x5/0xfbef5 (?:?)
__virt_addr_valid+0x188/0x2f0 (?:?)
kasan_report+0xe4/0x120 (?:?)
ocfs2_find_max_contig_free_bits+0x35/0x70 (fs/ocfs2/suballoc.c:1375)
ocfs2_block_group_set_bits+0x472/0x4b0 (fs/ocfs2/suballoc.c:1457)
ocfs2_cluster_group_search+0x16b/0x440 (fs/ocfs2/suballoc.c:86)
ocfs2_bg_discontig_fix_result+0x1ef/0x230 (fs/ocfs2/suballoc.c:1786)
ocfs2_search_chain+0x8f8/0x10a0 (fs/ocfs2/suballoc.c:1886)
get_page_from_freelist+0x70e/0x2370 (?:?)
lock_release+0xc6/0x290 (?:?)
do_raw_spin_unlock+0x9a/0x100 (?:?)
kasan_unpoison+0x27/0x60 (?:?)
__bfs+0x147/0x240 (?:?)
get_page_from_freelist+0x83d/0x2370 (?:?)
ocfs2_claim_suballoc_bits+0x38c/0xe70 (fs/ocfs2/suballoc.c:96)
sched_domains_numa_masks_clear+0x70/0xd0 (?:?)
check_irq_usage+0xe8/0xb70 (?:?)
__ocfs2_claim_clusters+0x18d/0x4c0 (fs/ocfs2/suballoc.c:2497)
check_path+0x24/0x50 (?:?)
rcu_is_watching+0x20/0x50 (?:?)
check_prev_add+0xfd/0xd00 (?:?)
ocfs2_add_clusters_in_btree+0x17d/0x810 (fs/ocfs2/suballoc.c:?)
__folio_batch_add_and_move+0x1f5/0x3d0 (?:?)
ocfs2_add_inode_data+0xd9/0x120 (fs/ocfs2/suballoc.c:?)
filemap_add_folio+0x105/0x1f0 (?:?)
ocfs2_write_begin_nolock+0x29f7/0x2f80 (fs/ocfs2/suballoc.c:3043)
ocfs2_read_inode_block+0xb5/0x110 (fs/ocfs2/suballoc.c:?)
down_write+0xf5/0x180 (?:?)
ocfs2_write_begin+0x180/0x240 (fs/ocfs2/suballoc.c:?)
__mark_inode_dirty+0x758/0x9a0 (?:?)
inode_to_bdi+0x41/0x90 (?:?)
balance_dirty_pages_ratelimited_flags+0xf8/0x1d0 (?:?)
generic_perform_write+0x252/0x440 (?:?)
mnt_put_write_access_file+0x16/0x70 (?:?)
file_update_time_flags+0xe4/0x200 (?:?)
ocfs2_file_write_iter+0x80a/0x1320 (fs/ocfs2/suballoc.c:?)
lock_acquire+0x184/0x2f0 (?:?)
ksys_write+0xd2/0x170 (?:?)
apparmor_file_permission+0xf5/0x310 (?:?)
read_zero+0x8d/0x140 (?:?)
lock_is_held_type+0x8f/0x100 (?:?)
CVSS Score
8.8
EPSS Score
0.005
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
hdlc_ppp: sync per-proto timers before freeing hdlc state
Each PPP control protocol (LCP/IPCP/IPV6CP) embedded in struct ppp
registers a timer via timer_setup(). That struct ppp is the
hdlc->state allocation, which detach_hdlc_protocol() frees with kfree()
in both teardown paths: unregister_hdlc_device() and the re-attach inside
attach_hdlc_protocol().
The ppp proto never registered a .detach callback, so
detach_hdlc_protocol() performs no timer synchronization before the
kfree(). The only cancel, timer_delete(&proto->timer) in ppp_cp_event(),
is partial (it does not wait for a running callback) and only runs on the
->CLOSED transition; ppp_stop()/ppp_close() do not sync either. A
ppp_timer callback already executing (blocked on ppp->lock) survives the
kfree and then dereferences proto->state / ppp->lock in freed memory,
leading to a use-after-free.
Fix this by adding a .detach helper that calls timer_shutdown_sync() on
every per-proto timer. detach_hdlc_protocol() invokes proto->detach(dev)
before kfree(hdlc->state), so timer_shutdown_sync()
now runs on both free paths.
timer_shutdown_sync() is used instead of timer_delete_sync() because the
keepalive path re-arms the timer through add_timer()/mod_timer() and
shutdown blocks any re-activation during teardown.
Initialize the per-protocol timers in ppp_ioctl() when the protocol is
attached, and remove the now-redundant timer_setup() from ppp_start(), so
that the timers are initialized exactly once at attach time and
ppp_timer_release() never operates on uninitialized timer_list
structures. attach_hdlc_protocol() uses kmalloc() (not kzalloc), so
struct ppp's protos[i].timer is uninitialized garbage until the first
timer_setup(); without this init-at-attach, attaching the PPP protocol
without ever bringing the device up would leave timer_shutdown_sync()
operating on uninitialized memory in .detach. Moving the init out of
ppp_start() (which only runs on NETDEV_UP) into the attach path makes the
initialization unconditional and avoids initializing the same timer_list
twice.
This bug was found by static analysis.
CVSS Score
7.8
EPSS Score
0.001
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
i2c: core: fix adapter registration race
Adapters can be looked up based on their id using i2c_get_adapter()
which takes a reference to the embedded struct device.
Make sure that the adapter (including its struct device) has been
initialised before adding it to the IDR to avoid accessing uninitialised
data which could, for example, lead to NULL-pointer dereferences or
use-after-free.
Note that the i2c-dev chardev, which is registered from a bus notifier,
currently uses i2c_get_adapter() so the adapter needs to be added to the
IDR before registration.
CVSS Score
7.8
EPSS Score
0.001
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
fbdev: omap2: fix use-after-free in omapfb_mmap
omapfb_mmap() has a race condition with OMAPFB_SETUP_PLANE ioctl that
can lead to use-after-free:
The fb_mmap() entry point holds mm_lock but not lock (fb_info->lock),
while ioctl handlers like OMAPFB_SETUP_PLANE hold lock but not mm_lock.
This allows concurrent execution.
In omapfb_mmap():
1. rg = omapfb_get_mem_region(ofbi->region); // Get old region ref
2. start = omapfb_get_region_paddr(ofbi); // Read from NEW region
3. len = fix->smem_len; // Read from NEW region
4. vm_iomap_memory(vma, start, len); // Map NEW region memory
5. atomic_inc(&rg->map_count); // Increment OLD region!
Concurrently, OMAPFB_SETUP_PLANE can:
- Reassign ofbi->region = new_rg
- Update fix->smem_len
- OMAPFB_SETUP_MEM then checks NEW region's map_count (0!) and frees it
This leaves userspace with a mapping to freed physical memory.
The fix is to read all required values (start, len) from the same
region reference (rg) that will have its map_count incremented,
preventing the region from being freed while still mapped.
CVSS Score
7.8
EPSS Score
0.002
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
fbdev: Fix fb_new_modelist to prevent null-ptr-deref in fb_videomode_to_var
info->var, a framebuffer's current mode, is expected to have a matching
entry in info->modelist. var_to_display() relies on this and treats a
failed fb_match_mode() as "This should not happen". fb_set_var() keeps it
true by adding the mode to the list on every change, and
do_register_framebuffer() does the same at registration.
store_modes() replaces the modelist from userspace. fb_new_modelist()
validates the new modes but does not check that info->var still has a
match. It relies on fbcon_new_modelist() to re-point consoles, but that
only handles consoles mapped to the framebuffer. With fbcon unbound there
are none, so info->var is left describing a mode that is no longer in the
list.
A later console takeover runs var_to_display(), where fb_match_mode()
returns NULL and leaves fb_display[i].mode NULL. fbcon_switch() passes it
to display_to_var(), and fb_videomode_to_var() dereferences the NULL mode.
Keep the current mode in the list in fb_new_modelist(), the same way
fb_set_var() does.
CVSS Score
5.5
EPSS Score
0.001
Published
2026-07-19