Linux: >> Linux Kernel >> 6.12.63 Security Vulnerabilities
In the Linux kernel, the following vulnerability has been resolved:
Input: elan_i2c - prevent division by zero and arithmetic underflow
The Elan I2C touchpad driver queries the device for its physical
dimensions and trace counts to calculate the device resolution and width.
However, if the device firmware or device tree provides invalid zero
values for x_traces or y_traces, it results in a fatal division-by-zero
exception leading to a kernel panic during device probe.
Add checks to ensure these parameters are non-zero before performing
the division. If invalid trace values are detected, fall back to a safe
default of 1.
Additionally, prevent an arithmetic underflow in the touch reporting
logic. Previously, if the calculated or fallback width was smaller than
ETP_FWIDTH_REDUCE (90), the subtraction would underflow, resulting in a
massive unsigned integer being reported to userspace. Clamp the adjusted
width to a minimum of 0 to safely handle small physical dimensions and
fallback scenarios.
Completing the probe with safe fallback values ensures the sysfs nodes
are created, keeping the firmware update path intact so a recovery
firmware can be flashed to the device.
CVSS Score
5.5
EPSS Score
0.002
Published
2026-07-25
In the Linux kernel, the following vulnerability has been resolved:
fuse: clear intr_entry in fuse_resend and fuse_remove_pending_req
When fuse_resend() moves a request from fpq->processing back to
fiq->pending, it sets FR_PENDING and clears FR_SENT but does not
remove the requests intr_entry from fiq->interrupts. If the
request had FR_INTERRUPTED set from a prior signal, intr_entry
remains dangling on fiq->interrupts. When the requesting task
then receives a fatal signal, fuse_remove_pending_req() sees
FR_PENDING=1, removes the request from fiq->pending and frees it
via the refcount path, also without cleaning intr_entry. The
stale intr_entry causes use-after-free when fuse_read_interrupt()
iterates fiq->interrupts:
- list_del_init(&req->intr_entry) -> UAF write on freed slab
- req->in.h.unique -> UAF read, data leaked to userspace
Remove intr_entry from fiq->interrupts in fuse_resend() for
interrupted requests before they are placed back on fiq->pending.
Add a WARN_ON if the intr_entry is not empty on request destruction.
CVSS Score
7.8
EPSS Score
0.002
Published
2026-07-25
In the Linux kernel, the following vulnerability has been resolved:
fuse: re-lock request before returning from fuse_ref_folio()
fuse_ref_folio() unlocks the request but does not re-lock it before
returning. fuse_chan_abort() can end the request and the async end
callback (eg fuse_writepage_free()) can free the args while the
subsequent copy chain logic after fuse_ref_folio() accesses them,
leading to use-after-free issues.
Fix this by locking the request in fuse_ref_folio() before returning.
CVSS Score
7.8
EPSS Score
0.002
Published
2026-07-25
In the Linux kernel, the following vulnerability has been resolved:
xfs: don't wrap around quota ids in dqiterate
LOLLM noticed that q_id is an unsigned 32-bit variable. If it happens
to be set to XFS_DQ_ID_MAX due to a filesystem that actually has a dquot
for ID_MAX, then this addition will truncate to zero and the iteration
starts over. Fix this by casting to u64.
CVSS Score
5.5
EPSS Score
0.002
Published
2026-07-25
In the Linux kernel, the following vulnerability has been resolved:
NTB: epf: Avoid pci_iounmap() with offset when PEER_SPAD and CONFIG share BAR
When BAR_PEER_SPAD and BAR_CONFIG share one PCI BAR, the module teardown
path ends up calling pci_iounmap() on the same iomem with some offset,
which is unnecessary and triggers a kernel warning like the following:
Trying to vunmap() nonexistent vm area (0000000069a5ffe8)
WARNING: mm/vmalloc.c:3470 at vunmap+0x58/0x68, CPU#5: modprobe/2937
[...]
Call trace:
vunmap+0x58/0x68 (P)
iounmap+0x34/0x48
pci_iounmap+0x2c/0x40
ntb_epf_pci_remove+0x44/0x80 [ntb_hw_epf]
pci_device_remove+0x48/0xf8
device_remove+0x50/0x88
device_release_driver_internal+0x1c8/0x228
driver_detach+0x50/0xb0
bus_remove_driver+0x74/0x100
driver_unregister+0x34/0x68
pci_unregister_driver+0x34/0xa0
ntb_epf_pci_driver_exit+0x14/0xfe0 [ntb_hw_epf]
[...]
Fix it by unmapping only when PEER_SPAD and CONFIG use difference bars.
CVSS Score
5.5
EPSS Score
0.002
Published
2026-07-24
In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mld: validate sta_mask before ffs() in BA session handlers
Three BA session handlers use ffs(ba_data->sta_mask) - 1 to derive a
station ID without checking that sta_mask is non-zero. When sta_mask is
zero, ffs() returns 0 and the subtraction wraps to 0xFFFFFFFF, causing
an out-of-bounds access on fw_id_to_link_sta[].
Add WARN_ON_ONCE(!ba_data->sta_mask) guards before each ffs() call,
consistent with the existing check in iwl_mld_ampdu_rx_start().
CVSS Score
8.8
EPSS Score
0.002
Published
2026-07-24
In the Linux kernel, the following vulnerability has been resolved:
pwrseq: core: fix use-after-free in pwrseq_debugfs_seq_next()
pwrseq_debugfs_seq_next() declares 'next' with __free(put_device),
which causes put_device() to be called on the returned pointer when
the variable goes out of scope. This results in a use-after-free
since the seq_file framework receives a pointer whose reference has
already been dropped.
Simply removing __free(put_device) would fix the UAF but would leak
the reference acquired by bus_find_next_device(), as stop() only
calls up_read(&pwrseq_sem) and never releases the device reference.
Fix this by making the reference counting consistent across all
seq_file callbacks, matching the standard pattern used by PCI and
SCSI:
- start(): use get_device() so it returns a referenced pointer.
- next(): explicitly put_device(curr) to release the previous
device's reference (no NULL check needed - the seq_file framework
only calls next() while the previous return was non-NULL).
- stop(): put_device(data) to release the last iterated device's
reference, with a NULL guard since stop() may be called with NULL
when start() returned NULL or next() reached end-of-sequence.
CVSS Score
7.8
EPSS Score
0.001
Published
2026-07-24
In the Linux kernel, the following vulnerability has been resolved:
MIPS: DEC: Prevent initial console buffer from landing in XKPHYS
In 64-bit configurations calling the initial console output handler from
a kernel thread other than the initial one will result in a situation
where the stack has been placed in the XKPHYS 64-bit memory segment and
consequently so has been the buffer allocated there that is used as the
argument corresponding to the `%s' output conversion specifier for the
firmware's printf() entry point.
This 64-bit address will then be truncated by 32-bit firmware, resulting
in an attempt to access the wrong memory location, which in turn will
cause all kinds of unpredictable behaviour, such as a kernel crash:
Console: colour dummy device 160x64
Calibrating delay loop... 49.36 BogoMIPS (lpj=192512)
pid_max: default: 32768 minimum: 301
CPU 0 Unable to handle kernel paging request at virtual address 000000000203bd00, epc == ffffffffbfc08364, ra == ffffffffbfc08800
Oops[#1]:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.18.0-rc2-00254-gfb649bda6f56-dirty #121
$ 0 : 0000000000000000 0000000000000001 0000000000000023 ffffffff80684ba0
$ 4 : 000000000203bd00 ffffffffbfc0f3b4 ffffffffffffffff 0000000000000073
$ 8 : 0a303d7469000000 0000000000000000 0000000000000073 ffffffffbfc0f473
$12 : 0000000000000002 0000000000000000 ffffffff80684c1c 0000000000000000
$16 : 0000000000000000 ffffffff80596dc9 0000000000000000 ffffffffbfc09240
$20 : ffffffff80684c40 ffffffffbfc0f400 000000000000002d 000000000000002b
$24 : ffffffffffffffbf 000000000203bd00
$28 : ffffffff805f0000 ffffffff80684b58 0000000000000030 ffffffffbfc08800
Hi : 0000000000000000
Lo : 0000000000000aa8
epc : ffffffffbfc08364 0xffffffffbfc08364
ra : ffffffffbfc08800 0xffffffffbfc08800
Status: 140120e2 KX SX UX KERNEL EXL
Cause : 00000008 (ExcCode 02)
BadVA : 000000000203bd00
PrId : 00000430 (R4000SC)
Modules linked in:
Process swapper (pid: 0, threadinfo=(____ptrval____), task=(____ptrval____), tls=0000000000000000)
Stack : 0000000000000000 0000000000000000 0000000000000000 0000004d0000004d
80684cc0806a2a40 80596dc80000004d 8061000000000000 bfc0850c80684c38
0000000000000000 000000000203bd00 0000000000000000 0000000000000000
0000000000000000 00000000bfc0f3b4 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000002500000000 0000000000000000 0000000000000000 802c1a7400000000
0203bd0080596dc8 0203bd4d69000000 6c61632000000018 5f746567646e6172
6c616320625f6d6f 5f736e5f6d6f7266 206361323778302b 303d74696e726320
806a0a38806b0000 806a0a38806b0000 00000000806b0000 80683c58806b0000
...
Call Trace:
Code: a082ffff 03e00008 00601021 <80820000> 00001821 10400005 24840001 80820000 24630001
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Fatal exception in interrupt
KN04 V2.1k (PC: 0xa0026768, SP: 0x806848e8)
>>
In this case the pointer in $4 was truncated from 0x980000000203bd00 to
0x000000000203bd00.
This may happen when no final console driver has been enabled in the
configuration and consequently the initial console continues being used
late into bootstrap or with an upcoming change that will switch the zs
driver to use a platform device, which in turn will make the console
handover happen only after other kernel threads have already been
started.
Fix the issue by making the buffer static and initdata, and therefore
placed in the CKSEG0 32-bit compatibility segment, observing that the
console output handler is called with the console lock held, implying
no need for this code to be reentrant. Add an assertion to verify the
buffer actually has been placed in a compatibility segment.
CVSS Score
5.5
EPSS Score
0.002
Published
2026-07-24
In the Linux kernel, the following vulnerability has been resolved:
mm/damon/sysfs-schemes: delete tried region in regions_rmdirs()
DAMON sysfs maintains the DAMOS tried region directory objects via a
linked list. When the user requests refresh of the directories, DAMON
sysfs removes all the region directories first, and then generate updated
regions directory on the empty space. The removal function
(damon_sysfs_scheme_regions_rm_dirs()) only puts the kobj objects.
Deletion of the container region object from the linked list is done
inside the kobj release callback function.
If somehow the callback invocation is delayed, the list will contain
regions list that gonna be freed. If the updated region directories
creation is started in this situation, the list can be corrupted and
use-after-free can happen.
Because the kobj objects are managed by only DAMON sysfs, the issue cannot
happen in normal situation. But, such delays can be made on kernels that
built with CONFIG_DEBUG_KOBJECT_RELEASE. On the kernel, the issue can
indeed be reproduced like below.
# damo start --damos_action stat
# cd /sys/kernel/mm/damon/admin/kdamonds/0/
# for i in {1..10}; do echo update_schemes_tried_regions > state; done
# dmesg | grep underflow
[ 89.296152] refcount_t: underflow; use-after-free.
Fix the issue by removing the region object from the list when
decrementing the reference count.
Also update damos_sysfs_populate_region_dir() to add the region object to
the list only after the kobject_init_and_add() is success, so that fail of
kobject_init_and_add() is not leaving the deallocated object on the list.
The issue was discovered [1] by Sashiko.
CVSS Score
7.8
EPSS Score
0.002
Published
2026-07-24
In the Linux kernel, the following vulnerability has been resolved:
gpio: rockchip: teardown bugs and resource leaks
Address several teardown issues and resource leaks in the driver's remove
path and error handling:
1. Debounce clock reference leak: The debounce clock (bank->db_clk) is
obtained using of_clk_get() which increments the clock's reference
count, but clk_put() is never called. Register a devm action to
cleanly release it on unbind. Note that of_clk_get(..., 1) remains
necessary over devm_clk_get() because the DT binding does not define
clock-names, precluding name-based lookup.
2. Unregistered chained IRQ handler: The chained IRQ handler is not
disconnected in remove(). If a stray interrupt fires after the driver
is removed, the kernel attempts to execute a stale handler, leading
to a panic. Fix this by clearing the handler in remove().
3. IRQ domain leak: The linear IRQ domain and its generic chips are
allocated manually during probe but never removed. Remove the IRQ
domain during driver teardown to free the associated generic chips
and mappings.
[Bartosz: don't emit an error message on devres allocation failure]
CVSS Score
5.5
EPSS Score
0.002
Published
2026-07-24