In the Linux kernel, the following vulnerability has been resolved:
spi: sprd: fix error pointer deref after DMA setup failure
The driver falls back to PIO mode if DMA setup fails during probe.
Make sure to check the dma.enabled flag before trying to release the DMA
channels also on late probe errors to avoid dereferencing an error
pointer (or attempting to release a channel a second time).
This issue was flagged by Sashiko when reviewing a devres allocation
conversion patch.
In the Linux kernel, the following vulnerability has been resolved:
ALSA: asihpi: Fix potential OOB array access at reading cache
find_control() to retrieve a cached info accesses the array with the
given index blindly, which may lead to an OOB array access.
Add a sanity check for avoiding it.
In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus/adm1266) widen blackbox-info buffer to I2C_SMBUS_BLOCK_MAX
adm1266_nvmem_read_blackbox() declares a 5-byte stack buffer and
passes it to i2c_smbus_read_block_data() to retrieve the 4-byte
BLACKBOX_INFO response. i2c_smbus_read_block_data() does not honour
caller buffer sizes -- it memcpy()s data.block[0] bytes from the
SMBus transaction (where data.block[0] is the length byte returned by
the slave device, up to I2C_SMBUS_BLOCK_MAX = 32):
memcpy(values, &data.block[1], data.block[0]);
If the device returns any block length above 5, the call overflows
the caller's 5-byte stack buffer before the post-call
if (ret != 4)
return -EIO;
check has a chance to reject the response.
Widen the local buffer to I2C_SMBUS_BLOCK_MAX so the helper has room
for any well-formed SMBus block response, matching the convention used
by the other i2c_smbus_read_block_data() callers in this driver.
In the Linux kernel, the following vulnerability has been resolved:
net: bcmgenet: keep RBUF EEE/PM disabled
Setting RBUF_EEE_EN | RBUF_PM_EN in RBUF_ENERGY_CTRL breaks the RX
path on GENET hardware once MAC EEE becomes active. RX traffic stops
flowing while the link stays up and the usual descriptor/RX error
counters remain quiet. In that state the MAC still accepts frames
(rbuf_ovflow_cnt keeps climbing) but RBUF no longer forwards them to
DMA, so rx_packets is no longer incremented at the netdev level. On
some boards the corruption ends up as a paging fault in
skb_release_data via bcmgenet_rx_poll on an LPI exit.
Reproduced on Pi 4B (BCM2711 + BCM54213PE) and confirmed by Florian
Fainelli on an internal Broadcom 4908-family board with the same crash
signature. RBUF_PM_EN is not publicly documented.
This shows up more often now that phy_support_eee() enables EEE by
default, but it also affects older kernels as soon as TX LPI is
turned on via ethtool, so it is not specific to recent changes.
Always clear RBUF_EEE_EN | RBUF_PM_EN in bcmgenet_eee_enable_set so
the bits stay off across resets. UMAC and TBUF setup is left alone so
TX-side EEE keeps working.
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: validate Add Extended Advertising Data length
MGMT_OP_ADD_EXT_ADV_DATA is registered as a variable-length command,
with MGMT_ADD_EXT_ADV_DATA_SIZE as the fixed header size. The handler
then uses cp->adv_data_len and cp->scan_rsp_len to validate and copy
cp->data, but it never checks that those bytes are part of the mgmt
command payload.
A short command can therefore make add_ext_adv_data() pass an
out-of-bounds pointer into tlv_data_is_valid(). If the bytes beyond
the command buffer are addressable, they can also be copied into the
advertising instance as scan response data, where the caller can read
them back via MGMT_OP_GET_ADV_INSTANCE. The trigger requires
CAP_NET_ADMIN in the initial user namespace; KASAN reports an 8-byte
slab-out-of-bounds read.
Reject commands whose length does not match the fixed header plus both
advertising data lengths before parsing cp->data.
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: drop ISO_END frames received without prior ISO_START
ISO data PDUs carry a packet-boundary flag indicating START, CONT, END
or SINGLE. The ISO_CONT branch of iso_recv() guards against a missing
ISO_START by checking conn->rx_len before touching conn->rx_skb, but
ISO_END does not.
If a peer sends an ISO_END as the first packet on a fresh ISO
connection, conn->rx_skb is still NULL and conn->rx_len is zero, so
skb_put(conn->rx_skb, ...) dereferences NULL and oopses. For BIS,
where receivers sync to a broadcaster without pairing, any broadcaster
on the air can trigger this.
Mirror the ISO_CONT check at the top of ISO_END so a stray end fragment
is logged and dropped instead of crashing the host.
In the Linux kernel, the following vulnerability has been resolved:
ipv6: ioam: add NULL check for idev in ipv6_hop_ioam()
Reported by Sashiko:
The function ipv6_hop_ioam() accesses
__in6_dev_get(skb->dev)->cnf.ioam6_enabled without validating the returned
idev pointer. Because addrconf_ifdown() can concurrently clear dev->ip6_ptr
via RCU, __in6_dev_get() can return NULL during interface teardown, which
could cause a NULL pointer dereference when processing an IOAM Hop-by-Hop
option.
Let's add a check and use SKB_DROP_REASON_IPV6DISABLED accordingly.
In the Linux kernel, the following vulnerability has been resolved:
qed: fix double free in qed_cxt_tables_alloc()
If one of the later PF or VF CID bitmap allocations fails,
qed_cid_map_alloc() jumps to cid_map_fail and frees the previously
allocated CID bitmaps before returning an error. qed_cxt_tables_alloc()
then calls qed_cxt_mngr_free(), which invokes qed_cid_map_free()
again.
Fix this by setting each CID bitmap pointer to NULL after bitmap_free()
to avoid double free.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1-rc3.
Runtime reproduction was not attempted because exercising the failing
allocation path requires device-specific setup.
In the Linux kernel, the following vulnerability has been resolved:
net: ifb: report ethtool stats over num_tx_queues
ifb_dev_init() allocates dp->tx_private to dev->num_tx_queues
entries via kzalloc_objs(*txp, dev->num_tx_queues). Both IFB
per-queue RX and TX stats live in those entries: ifb_xmit() updates
txp->rx_stats using the skb queue mapping, ifb_ri_tasklet() updates
txp->tx_stats, and ifb_stats64() aggregates both over
dev->num_tx_queues.
The ethtool stats callbacks instead size and walk the per-queue
stats with dev->real_num_rx_queues and dev->real_num_tx_queues. With
an asymmetric device where the RX queue count exceeds the TX queue
count, for example:
ip link add name ifb10 numtxqueues 1 numrxqueues 8 type ifb
ethtool -S ifb10
ifb_get_ethtool_stats() indexes past the tx_private allocation and
copies adjacent slab data through ETHTOOL_GSTATS.
Use dev->num_tx_queues consistently for the stats strings, the
stats count, and the stats data walks. This reports one RX stats
group and one TX stats group for each backing ifb_q_private entry,
which is the queue set IFB can actually populate.
Reproduced under UML+KASAN at v7.1-rc2:
BUG: KASAN: slab-out-of-bounds in ifb_fill_stats_data+0x3c/0xae
Read of size 8 at addr 0000000062dbd228 by task ethtool/36
ifb_fill_stats_data+0x3c/0xae
ifb_get_ethtool_stats+0xc0/0x129
__dev_ethtool+0x1ca5/0x363c
dev_ethtool+0x123/0x1b3
dev_ioctl+0x56c/0x744
sock_do_ioctl+0x15f/0x1b2
sock_ioctl+0x4d5/0x50a
sys_ioctl+0xd8b/0xde9
With the patch applied, the same UML+KASAN repro is silent and
ethtool -S ifb10 reports only the stats backed by the single
allocated tx_private entry.