Linux: >> Linux Kernel >> 2.6.13.5 Security Vulnerabilities
In the Linux kernel, the following vulnerability has been resolved:
Input: iforce - bound the device-reported force-feedback effect index
iforce_process_packet() handles a status report (packet id 0x02) by
taking a force-feedback effect index straight from the device wire and
using it to address the per-effect state array:
i = data[1] & 0x7f;
if (data[1] & 0x80) {
if (!test_and_set_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags))
...
} else if (test_and_clear_bit(FF_CORE_IS_PLAYED,
iforce->core_effects[i].flags)) {
...
}
The index is masked only with 0x7f, so it ranges 0..127, but
core_effects[] holds only IFORCE_EFFECTS_MAX (32) entries. For an index
of 32..127 the test_and_set_bit()/test_and_clear_bit() is an
out-of-bounds single-bit read-modify-write past the array. core_effects[]
is the second-to-last member of struct iforce, so the write lands in the
trailing members and beyond the embedding kzalloc()'d iforce_serio /
iforce_usb object.
data[1] is unvalidated device payload on both transports (the USB
interrupt endpoint and serio), and the status path is not gated on force
feedback being present, so a malicious or counterfeit device can set or
clear a bit at an attacker-chosen offset past the object.
Reject an out-of-range index instead of indexing with it. Bound against
the array dimension IFORCE_EFFECTS_MAX rather than dev->ff->max_effects so
the check guarantees memory safety regardless of how many effects the
device registered. A legitimate "effect started/stopped" status always
carries an index below IFORCE_EFFECTS_MAX, so well-formed devices are
unaffected; the neighbouring mark_core_as_ready() loop is already bounded
and is left untouched.
CVSS Score
7.8
EPSS Score
0.002
Published
2026-07-25
In the Linux kernel, the following vulnerability has been resolved:
MIPS: DEC: Prevent initial console buffer from landing in XKPHYS
In 64-bit configurations calling the initial console output handler from
a kernel thread other than the initial one will result in a situation
where the stack has been placed in the XKPHYS 64-bit memory segment and
consequently so has been the buffer allocated there that is used as the
argument corresponding to the `%s' output conversion specifier for the
firmware's printf() entry point.
This 64-bit address will then be truncated by 32-bit firmware, resulting
in an attempt to access the wrong memory location, which in turn will
cause all kinds of unpredictable behaviour, such as a kernel crash:
Console: colour dummy device 160x64
Calibrating delay loop... 49.36 BogoMIPS (lpj=192512)
pid_max: default: 32768 minimum: 301
CPU 0 Unable to handle kernel paging request at virtual address 000000000203bd00, epc == ffffffffbfc08364, ra == ffffffffbfc08800
Oops[#1]:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.18.0-rc2-00254-gfb649bda6f56-dirty #121
$ 0 : 0000000000000000 0000000000000001 0000000000000023 ffffffff80684ba0
$ 4 : 000000000203bd00 ffffffffbfc0f3b4 ffffffffffffffff 0000000000000073
$ 8 : 0a303d7469000000 0000000000000000 0000000000000073 ffffffffbfc0f473
$12 : 0000000000000002 0000000000000000 ffffffff80684c1c 0000000000000000
$16 : 0000000000000000 ffffffff80596dc9 0000000000000000 ffffffffbfc09240
$20 : ffffffff80684c40 ffffffffbfc0f400 000000000000002d 000000000000002b
$24 : ffffffffffffffbf 000000000203bd00
$28 : ffffffff805f0000 ffffffff80684b58 0000000000000030 ffffffffbfc08800
Hi : 0000000000000000
Lo : 0000000000000aa8
epc : ffffffffbfc08364 0xffffffffbfc08364
ra : ffffffffbfc08800 0xffffffffbfc08800
Status: 140120e2 KX SX UX KERNEL EXL
Cause : 00000008 (ExcCode 02)
BadVA : 000000000203bd00
PrId : 00000430 (R4000SC)
Modules linked in:
Process swapper (pid: 0, threadinfo=(____ptrval____), task=(____ptrval____), tls=0000000000000000)
Stack : 0000000000000000 0000000000000000 0000000000000000 0000004d0000004d
80684cc0806a2a40 80596dc80000004d 8061000000000000 bfc0850c80684c38
0000000000000000 000000000203bd00 0000000000000000 0000000000000000
0000000000000000 00000000bfc0f3b4 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000002500000000 0000000000000000 0000000000000000 802c1a7400000000
0203bd0080596dc8 0203bd4d69000000 6c61632000000018 5f746567646e6172
6c616320625f6d6f 5f736e5f6d6f7266 206361323778302b 303d74696e726320
806a0a38806b0000 806a0a38806b0000 00000000806b0000 80683c58806b0000
...
Call Trace:
Code: a082ffff 03e00008 00601021 <80820000> 00001821 10400005 24840001 80820000 24630001
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Fatal exception in interrupt
KN04 V2.1k (PC: 0xa0026768, SP: 0x806848e8)
>>
In this case the pointer in $4 was truncated from 0x980000000203bd00 to
0x000000000203bd00.
This may happen when no final console driver has been enabled in the
configuration and consequently the initial console continues being used
late into bootstrap or with an upcoming change that will switch the zs
driver to use a platform device, which in turn will make the console
handover happen only after other kernel threads have already been
started.
Fix the issue by making the buffer static and initdata, and therefore
placed in the CKSEG0 32-bit compatibility segment, observing that the
console output handler is called with the console lock held, implying
no need for this code to be reentrant. Add an assertion to verify the
buffer actually has been placed in a compatibility segment.
CVSS Score
5.5
EPSS Score
0.001
Published
2026-07-24
In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mld: don't dereference a pointer before NULL checking it
In iwl_mld_remove_link, the link->fw_id is saved at the beginning of the
function so we have it after we freed the link.
But the link pointer can be NULL, and is not checked when the fw_id is
stored.
Fix it by simply freeing the link at the end of the function.
fFixes: 0e66a39f4f0e ("wifi: iwlwifi: fix potential use after free in iwl_mld_remove_link()")
CVSS Score
5.5
EPSS Score
0.001
Published
2026-07-24
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: bnep: Fix UAF read of dev->name
bnep_add_connection() needs to keep holding the bnep_session_sem while
reading dev->name (just like bnep_get_connlist() does); otherwise the
bnep_session() thread can concurrently free the net_device, which can for
example be triggered by a concurrent bnep_del_connection().
(This UAF is fairly uninteresting from a security perspective;
calling bnep_add_connection() requires passing a capable(CAP_NET_ADMIN)
check. It also requires completely tearing down a netdev during a fairly
tight race window.)
CVSS Score
8.8
EPSS Score
0.002
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
ipv4: raw: reject IP_HDRINCL packets with ihl < 5
raw_send_hdrinc() validates that the caller-supplied IPv4 header
fits within the message length:
iphlen = iph->ihl * 4;
err = -EINVAL;
if (iphlen > length)
goto error_free;
if (iphlen >= sizeof(*iph)) {
/* fix up saddr, tot_len, id, csum, transport_header */
}
It does not, however, reject ihl < 5. For such a packet the
"if (iphlen >= sizeof(*iph))" branch is skipped, leaving the
crafted iphdr untouched, but the packet is still handed to
__ip_local_out() and onward. Downstream consumers that read
iph->ihl assume a sane value: net/ipv4/ah4.c:ah_output() in
particular subtracts sizeof(struct iphdr) from top_iph->ihl * 4
and passes the (signed-int-negative, then cast to size_t)
result to memcpy(), producing an OOB access of length close to
SIZE_MAX and a host kernel panic.
An IPv4 header with ihl < 5 is malformed by definition (RFC 791:
"Internet Header Length is the length of the internet header in
32 bit words ... Note that the minimum value for a correct header
is 5."). The kernel should not be willing to inject such a
packet into its own output path.
Reject "iphlen < sizeof(*iph)" alongside the existing
"iphlen > length" check. This matches the principle that locally
constructed packets that re-enter the IP stack must pass the same
basic sanity tests that a foreign packet would be subjected to.
Once this lands, the "if (iphlen >= sizeof(*iph))" wrapper around
the fixup branch becomes redundant; left in place to keep the
patch minimal and backport-friendly. A follow-up can unwrap it.
Note that commit 86f4c90a1c5c ("ipv4, ipv6: ensure raw socket
message is big enough to hold an IP header") ensures the message
buffer is large enough to hold an iphdr, but does not constrain
the self-reported iph->ihl.
Reachability: the malformed packet source is any caller with
CAP_NET_RAW, including an unprivileged process in a user+net
namespace on a kernel with CONFIG_USER_NS=y. The reproduced AH
crash also requires a matching xfrm AH policy on the outgoing
route; a container granted CAP_NET_ADMIN can install that state
and policy in its netns. Loopback bypasses xfrm_output, so the
trigger uses a real netdev.
Reproduced on UML + KASAN: kernel-mode fault at addr 0x0 with
memcpy_orig at the crash site. Same shape reproduces inside a
rootless Docker container with --cap-add NET_ADMIN on a stock
distro kernel.
CVSS Score
7.8
EPSS Score
0.001
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
hdlc_ppp: sync per-proto timers before freeing hdlc state
Each PPP control protocol (LCP/IPCP/IPV6CP) embedded in struct ppp
registers a timer via timer_setup(). That struct ppp is the
hdlc->state allocation, which detach_hdlc_protocol() frees with kfree()
in both teardown paths: unregister_hdlc_device() and the re-attach inside
attach_hdlc_protocol().
The ppp proto never registered a .detach callback, so
detach_hdlc_protocol() performs no timer synchronization before the
kfree(). The only cancel, timer_delete(&proto->timer) in ppp_cp_event(),
is partial (it does not wait for a running callback) and only runs on the
->CLOSED transition; ppp_stop()/ppp_close() do not sync either. A
ppp_timer callback already executing (blocked on ppp->lock) survives the
kfree and then dereferences proto->state / ppp->lock in freed memory,
leading to a use-after-free.
Fix this by adding a .detach helper that calls timer_shutdown_sync() on
every per-proto timer. detach_hdlc_protocol() invokes proto->detach(dev)
before kfree(hdlc->state), so timer_shutdown_sync()
now runs on both free paths.
timer_shutdown_sync() is used instead of timer_delete_sync() because the
keepalive path re-arms the timer through add_timer()/mod_timer() and
shutdown blocks any re-activation during teardown.
Initialize the per-protocol timers in ppp_ioctl() when the protocol is
attached, and remove the now-redundant timer_setup() from ppp_start(), so
that the timers are initialized exactly once at attach time and
ppp_timer_release() never operates on uninitialized timer_list
structures. attach_hdlc_protocol() uses kmalloc() (not kzalloc), so
struct ppp's protos[i].timer is uninitialized garbage until the first
timer_setup(); without this init-at-attach, attaching the PPP protocol
without ever bringing the device up would leave timer_shutdown_sync()
operating on uninitialized memory in .detach. Moving the init out of
ppp_start() (which only runs on NETDEV_UP) into the attach path makes the
initialization unconditional and avoids initializing the same timer_list
twice.
This bug was found by static analysis.
CVSS Score
7.8
EPSS Score
0.001
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
fbdev: Fix fb_new_modelist to prevent null-ptr-deref in fb_videomode_to_var
info->var, a framebuffer's current mode, is expected to have a matching
entry in info->modelist. var_to_display() relies on this and treats a
failed fb_match_mode() as "This should not happen". fb_set_var() keeps it
true by adding the mode to the list on every change, and
do_register_framebuffer() does the same at registration.
store_modes() replaces the modelist from userspace. fb_new_modelist()
validates the new modes but does not check that info->var still has a
match. It relies on fbcon_new_modelist() to re-point consoles, but that
only handles consoles mapped to the framebuffer. With fbcon unbound there
are none, so info->var is left describing a mode that is no longer in the
list.
A later console takeover runs var_to_display(), where fb_match_mode()
returns NULL and leaves fb_display[i].mode NULL. fbcon_switch() passes it
to display_to_var(), and fb_videomode_to_var() dereferences the NULL mode.
Keep the current mode in the list in fb_new_modelist(), the same way
fb_set_var() does.
CVSS Score
5.5
EPSS Score
0.001
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
nfsd: fix posix_acl leak on SETACL decode failure
nfsaclsvc_decode_setaclargs() and nfs3svc_decode_setaclargs() each
call nfs_stream_decode_acl() twice, first for NFS_ACL and then for
NFS_DFACL. Each successful call transfers ownership of a freshly
allocated posix_acl into argp->acl_access or argp->acl_default. If
the first call succeeds but the second fails, the decoder returns
false and argp->acl_access is left dangling.
ACLPROC2_SETACL.pc_release was wired to nfssvc_release_attrstat and
ACLPROC3_SETACL.pc_release was wired to nfs3svc_release_fhandle.
Both only call fh_put() and have no knowledge of the ACL fields on
argp. The posix_acl_release() pairs sat at the out: labels inside
nfsacld_proc_setacl() and nfsd3_proc_setacl(), but svc_process()
skips pc_func when pc_decode returns false, so that cleanup is
unreachable on decode failure:
svc_process_common()
pc_decode() /* decode_setaclargs: false */
/* pc_func skipped */
pc_release() /* fh_put only -- ACLs leaked */
The orphaned posix_acl is leaked for the lifetime of the server.
Fix by adding nfsaclsvc_release_setacl() and nfs3svc_release_setacl(),
which release both argp->acl_access and argp->acl_default in addition
to fh_put(), and wiring them as pc_release for their respective SETACL
procedures. pc_release runs on every path svc_process() takes after
decode, including decode failure, so the posix_acl_release() pairs are
removed from the proc functions' out: labels to keep ownership in one
place. This matches the existing release_getacl() pattern used by
the sibling GETACL procedures.
CVSS Score
7.5
EPSS Score
0.005
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
udf: reject descriptors with oversized CRC length
udf_read_tagged() skips CRC verification when descCRCLength +
sizeof(struct tag) exceeds the block size. A crafted UDF image can
set descCRCLength to an oversized value to bypass CRC validation
entirely; the descriptor is then accepted based solely on the 8-bit
tag checksum, which is trivially recomputable.
Reject such descriptors instead of silently accepting them. A
legitimate single-block descriptor should never have a CRC length that
exceeds the block.
CVSS Score
8.4
EPSS Score
0.001
Published
2026-07-19
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: bnep: reject short frames before parsing
A BNEP peer can send a short BNEP SDU. bnep_rx_frame() reads the
packet type byte immediately and, for control packets, reads the control
opcode and setup UUID-size byte before proving that those bytes are
present. bnep_rx_control() also dereferences the control opcode without
rejecting an empty control payload.
Use skb_pull_data() for the fixed fields in bnep_rx_frame() so a NULL
return gates each dereference. Split the control handler so the frame
path can pass an opcode that has already been pulled, and keep the
byte-buffer wrapper for extension control payloads.
For BNEP_SETUP_CONN_REQ, name the UUID-size byte before pulling the
setup payload. struct bnep_setup_conn_req carries destination and source
service UUIDs after that byte, each uuid_size bytes, so the parser now
documents that tuple explicitly instead of leaving the pull length as an
opaque multiplication.
Validation reproduced this kernel report:
KASAN slab-out-of-bounds in bnep_rx_frame.isra.0+0x130c/0x1790
The buggy address belongs to the object at ffff88800c0f7908 which belongs
to the cache kmalloc-8 of size 8
The buggy address is located 0 bytes to the right of allocated 1-byte
region [ffff88800c0f7908, ffff88800c0f7909)
Read of size 1
Call trace:
dump_stack_lvl+0xb3/0x140 (?:?)
print_address_description+0x57/0x3a0 (?:?)
bnep_rx_frame+0x130c/0x1790 (net/bluetooth/bnep/core.c:306)
print_report+0xb9/0x2b0 (?:?)
__virt_addr_valid+0x1ba/0x3a0 (?:?)
srso_alias_return_thunk+0x5/0xfbef5 (?:?)
kasan_addr_to_slab+0x21/0x60 (?:?)
kasan_report+0xe0/0x110 (?:?)
process_one_work+0xfce/0x17e0 (kernel/workqueue.c:3200)
worker_thread+0x65c/0xe40 (?:?)
__kthread_parkme+0x184/0x230 (?:?)
kthread+0x35e/0x470 (?:?)
_raw_spin_unlock_irq+0x28/0x50 (?:?)
ret_from_fork+0x586/0x870 (?:?)
__switch_to+0x74f/0xdc0 (?:?)
ret_from_fork_asm+0x1a/0x30 (?:?)
CVSS Score
7.1
EPSS Score
0.003
Published
2026-06-25
Page 1